Bmw R1150 R Abs Maintenance Manual-21215B240093.pdf -Bookmark created by https://wimanual.com Maintenance BMW Integral ABS Maintenance schedule Pre-delivery check Service data 00 Tightening torque Table of operating fluids Tightening torque Table of operating fluids 00 Pre-delivery check General view of crated motorcycle Checking the shipping pallet for damage In case of damage in Germany In case of damage in importer markets Unpacking the motorcycle Installing remaining items on motorcycle Mounting the Speedster fairing Inspecting motorcycle for damage Checking that delivery is complete Filling and charging the battery Removing the fuel tank Filling and charging the battery Checking engine oil when engine is cold, topping up if necessary Checking headlight beam angle, adjusting if necessary Checking tightness of rear wheel studs Checking tyre pressures [IntegralABS] Performing bleed test with BMWMoDiTeC Final inspection and function check Final cleaning Handing over the motorcycle 00 Maintenance Key to maintenance intervals Reading the BMWMoDiTeC fault code memory (Inspections I, II, III and IV) [Integral ABS] Performing bleed test with BMWMoDiTeC (Inspections I, II, III and IV) Changing engine oil, replacing oil filter element (Inspections I, II, III and IV) Changing the transmission oil (Inspections III and IV) or at least every 2 years Changing the oil in the rear wheel drive (Inspections I, III and IV) Every 40,000 km (24,000 miles) or at the latest every 2 years Replacing fuel filter (Inspection III) In normal operating conditions every 40,000 km (24,000 miles); if fuel quality is poor every 20,0... Checking battery fluid level and topping up if necessary; cleaning and greasing the battery termi... (Inspections III and IV) Replacing intake air filter element (Inspection III) In very dirty and dusty operating conditions, replace every 10,000 km (6,000 miles) or even more ... Replacing poly-V belt (Inspection III) every 60,000 km (36,000 miles) [Without IntegralABS] Checking brake fluid level (Inspections II and III) Front brake Rear brake [IntegralABS] Checking brake fluid level (Inspections II and III) Front brake Rear brake Checking brake system for correct operation and freedom from leaks; repairing (Inspection III) Checking brake pads and discs for wear (Inspections II and III) Checking front brake pad wear Checking rear brake pad wear Checking brake disc wear Replacing brake pads, front brake Replacing brake pads, rear brake [Without IntegralABS] Changing brake fluid and bleeding the brake system Change the brake fluid annually (Inspection IV) [Without IntegralABS] Bleeding [Without IntegralABS] Bleeding [IntegralABS] Changing Change brake fluid in wheel circuit once a year (Inspection IV) [IntegralABS] Bleeding [IntegralABS] Bleeding [IntegralABS] Changing Change brake fluid in control circuit every 2years (Inspection IV) [IntegralABS] Bleeding [IntegralABS] Bleeding Checking clutch operating fluid level (Inspections II and III) Changing the clutch fluid (Inspection IV) at least every 2 years Checking tightness of rear wheel studs (Inspection I) Checking rear wheel bearing play by tilting wheel (Inspection III) Checking swinging arm bearings, adjusting if necessary (Inspections I and III) Greasing the side stand pivot (Inspections I, II and III) Checking function of side stand contact switch (Inspections I, II, III and IV) Checking (Inspection II) check Tightening cylinder heads (Inspection I) Checking (Inspections I, II and III) Checking throttle cable freedom of movement, checking for chafes and kinks, replacing if necessar... (Inspections I, II and III) Final inspection with road safety and functional check (Inspections I, II, III and IV) Road safety check Roadworthiness check 34 Brakes Technical Data Removing and refitting front brake caliper Disassembling and assembling front brake caliper Removing and refitting rear brake caliper Disassembling and assembling rear brake caliper Dismantling rear brake caliper Assembling rear brake caliper Removing and refitting front brake discs Removing and refitting rear brake disc [Integral ABS] Removing and refitting front ABS sensor [Integral ABS] Removing and refitting rear ABS sensor Removing and refitting footbrake lever Removing and refitting brake master cylinder Checking and adjusting piston rod play Removing and refitting brake piston in handlebar fitting (a 32.7) [Integral ABS] Removing Removing the ABS pressure modulator Installing the ABS pressure modulator [Integral ABS] Draining brake system Bleeding wheel circuits Bleeding front wheel circuit Bleeding rear wheel circuit Bleeding control circuits Bleeding front control circuit Bleeding rear control circuit [Integral ABS] Filling the brake system Filling control circuits Filling the front control circuit Filling the rear control circuit Filling wheel circuits Filling the front wheel circuit Frontwheel circuit reservoirfilling instructions Filling rear wheel circuit Rear wheelcircuitfilling instructions [Integral ABS] Reading fault code memory with BMWMoDiTeC [IntegralABS] Performing a bleed test with BMWMoDiTeC [Integral ABS] Removing Removing [Integral ABS] Removing Removing and refitting front brake line Removing and refitting rear brake line . Notice: This is a preview not fully updated, please download the full version at https://wimanual.com