Bmw R1150 Rt Abs Maintenance Manual-21215B240094.pdf -Bookmark created by https://wimanual.com Maintenance BMW Integral ABS Maintenance schedule Pre-delivery check Service data 00 Tightening torque Table of operating fluids Tightening torque Table of operating fluids 00 Pre-delivery check General view of crated motorcycle Checking the crated motorcycle for damage In case of damage in Germany In case of damage in importer markets Unpacking the motorcycle Assembling the motorcycle Installing the front wheel Installing front mudguard Filling and charging the battery Installing cover for windscreen adjuster and installing windscreen Installing mirrors Assembling case Inspecting motorcycle for damage Checking that delivery is complete Checking engine oil level when cold, adding oil if necessary Checking tightness of rear wheel studs Checking tyre pressures Checking headlight beam angle, adjusting if necessary IntegralABS Performing bleed test with BMWMoDiTeC Final inspection and function check Final cleaning Handing over the motorcycle 00 Maintenance Key to maintenance intervals Reading the BMWMoDiTeC fault code memory (Inspections I, II, III and IV) IntegralABS: Performing bleed test with BMWMoDiTeC (Inspections I, II, III and IV) Changing engine oil, replacing oil filter element (Inspections I, II, III and IV) Changing oil in gearbox (Inspections III and IV) or at the latest every 2 years Changing the oil in the rear wheel drive (Inspections I, III and IV) every 40,000 km (24,000 miles) or at the latest every 2 years Replacing fuel filter (Inspection III) In normal operating conditions every 40,000 km (24,000 miles); if fuel quality is poor every 20,0... Checking battery fluid level and topping up if necessary; cleaning and greasing the battery posts (Inspections III and IV) Replacing intake air filter element (Inspection III) in very dirty and dusty operating conditions, replace every 10,000 km (6,000 miles) or even more ... Replacing Poly-V belt (Inspection III) every 60,000 km (36,000 miles) Checking brake fluid level (Inspections II and III) Front brake Rear brake Checking brake system for correct operation and freedom from leaks; repairing (Inspection III) Checking brake pads and discs for wear (Inspections II and III) Checking brake pads for wear Brake pads, front brake Brake pads, rear brake Checking brake disc wear Replacing brake pads Brake pads, front brake Brake pads, rear brake Changing Change brake fluid in wheel circuit once a year (Inspection IV) Bleeding Instructions for filling frontwheel circuitreservoir Bleeding Instructions for filling rearwheel circuitreservoir Changing Change brake fluid in control circuit every 2 years (Inspection IV) Bleeding Bleeding Checking clutch operating fluid level (Inspections II and III) Changing the clutch fluid (Inspection IV) every 2 years at the latest Checking tightness of rear wheel studs (Inspection I) Checking rear wheel bearing play by tilting wheel (Inspection III) Checking swinging arm bearings, adjusting if necessary (Inspections I and III) Greasing the side stand pivot (Inspections I, II and III) Checking function of side stand contact switch (Inspections I, II, III and IV) Checking (Inspection II) check Tightening cylinder heads (Inspection I) Checking (Inspections I, II and III) Checking freedom of throttle cable, checking for chaffing and kinks, replacing if necessary Check... (Inspections I, II and III) Final inspection with road safety and functional check (Inspections I, II, III and IV) Road safety check Roadworthiness check 34 Brakes Technical Data 34 Brakes Removing and installing front brake caliper Disassembling and assembling front brake caliper Removing and installing rear brake caliper Disassembling and assembling rear brake caliper Disassembling rear brake caliper Assembling rear brake caliper Removing and installing front brake discs Removing and installing rear brake disc Removing and installing Integral ABS sensor Removing and installing front Integral ABS sensor Removing and installing rear Integral ABS sensor Removing and installing footbrake lever Removing and installing rear brake master cylinder Checking and adjusting blow-by clearance of piston rod Checking blow-by clearance of piston rod Adjusting blow-by clearance at piston rod Checking and adjusting setting of rear brake light switch Checking setting of brake light switch, rear Adjusting brake light switch, rear Removing and installing piston in brake-lever fitting Removing and installing Integral ABS pressure modulator Removing Integral ABS pressure modulator Installing Integral ABS pressure modulator Draining the Integral ABS brake system Drain both wheel circuits Draining front wheel circuit Draining rear wheel circuit Draining control circuits Draining front control circuit Draining rear control circuit Filling and bleeding Integral ABS system Filling and bleeding control circuits Filling the front control circuit Bleeding front control circuit Filling the rear control circuit Bleeding the rear control circuit Filling and bleeding wheel circuits Filling and bleeding front wheel circuit Instructions for filling frontwheel circuitreservoir Filling and bleeding rear wheel circuit Instructions for filling rearwheel circuitreservoir Integral ABS Reading fault memory with BMWMoDiTeC IntegralABS Performing bleed test with BMWMoDiTeC Integral ABS Removing and installing bleed lines, wheel circuit reservoirs Integral ABS: Removing and installing brake lines Installed position of front brake line Installed position of rear brake line . Notice: This is a preview not fully updated, please download the full version at https://wimanual.com